Group items tagged

All of the procedures take a discrete ``gear'' to specify the speed. The reasons for this are two-fold; first, by limiting the power of the truck, we simplify the interface to children. Secondly, it allows use to calibrate the ``gears'' so that, for example, 10 seconds forward in first gear is the same distance as 10 seconds backward in first gear.

The limitation of LOGO however is the lack of feedback from the environment. There is no way of expressing an event occuring in the outside world.

Simple constructs in iLogo extend the original LOGO language with interactivity capabilities of reading sensors and transfering control to different parts of the program.

attach your Pager Motors to your Popper using two Fuse Clips, two Small Paper Clips, and no solder

It's simply a Phototropic BiCore driving two small motors

I had to add resistors across the motor leads to slow them down! I got this idea from Ben Hitchcock's Fred Troubleshooting Page -- "D) If the motor fires strongly once..."

I wanted to share an adaptation of the Schead v4, that I have been experimenting with. It is (for lack of a better term) a Master/Slave Schmitt Comparitor Head (M/S SC-H). With the addition of a 74 AC 240 or two (as motor drivers) and a pair of motors, you can put together an interesting little light seeking, wheeled robot with peripheral vision.

As long as the light reaching the photo-bridge of the Master SC-H is balanced, then the Slave SC-H acts as a regular, lone SC-H would. So, if one of the slave photo-diodes detects more light then the other, the inverter that controls the motor on that side changes states and is now the same as the inverter of the Master SC-H tied to the same motor. This turns that motor off and the robot will pivot around the stopped wheel toward the greater light source until the light on each sensors is balanced and the motor again begins to turn.

I am also using SCar to continue experimenting with Stacking separate Sensor/Behavior circuits onto a robot. I will post more as progress is made.

Droidmakr (Cliff Boerema) came up with an interesting idea for a light-tracking head with a form of peripheral vision. As often happens, the circuit turned into something different -- a photopopper:

All done with a single 74HC14 (the '240 being a motor driver).

I tried the same setup with the 74*240 (with an extra inverter per motor) and 7404, but the 74HC14 seems to work best.

This is the 3 capacitor method.  I used this one in all my RC cars and many of the RC toys that I have taken apart use this method.

One of the easiest and most overlooked technique that can be done to lower motor noise is the twist your motor and motor power wires.  This in affect forces the magnetic fields to cancel each other out.

By placing a metal shield between your motors and radio can do wonders.  Also keep in mind that some metals shield better than others.   Carbon Steel shields several hundred times better than aluminum.  Dont use this shielding as a conductor or you may compound the problem.

Most BEAMbot designs require at least 3 volts from their solar cell(s). This means, of course, that if you buy 0.5 V cells, you need to wire together at least six of them to do the job. This may or may not be something you want to mess with; it may or may not fit with the aesthetic design you're shooting for.

The Sharp IR Range Finder works by the process of triangulation. A pulse of light (wavelength range of 850nm +/-70nm) is emitted and then reflected back (or not reflected at all). When the light returns it comes back at an angle that is dependent on the distance of the reflecting object. Triangulation works by detecting this reflected beam angle - by knowing the angle, distance can then be determined.

The IR range finder reciever has a special precision lens that transmits the reflected light onto an enclosed linear CCD array based on the triangulation angle.

The Sharp IR has a non-linear output. This means that as the distance increases linearly (by set increments), the analog output increases/decreases non-linearly.

Behavior-based robotics is quite simply the design of robots where there are no internal "models" of the environment. Instead, the robot's action is state-machine driven via inputs gleaned from the robot's sensors.

The robots do not build a model of their world they simply act in response to the things they encounter whilst existing there.

This form of robotics has proved to be successful in environments that are unknown to the robot, environments that are busy or noisy such as a place with moving objects or people

An important part of the behaviour based theory is "embodiment" This means that a robot must be embodied, have a presence (it is an entity in itself).  In order to react the robot must be surrounded by the real world.

This book provides far more detail on the hardware aspects of robot building than any other I have seen to date and is worth picking up.

"Intermediate Robot Building" offers the kind of real-world knowledge that only an experienced robot builder can offer--the kind of knowledge beginners usually have to learn through mistakes. In this book, you'll learn the value of a robot heartbeat and the purpose of the wavy lines in photocells.