Group items tagged

how to interpret sensor data into a mathematical form readable by computers

There are only 3 steps you need to follow: Gather Sensor Data (data logging) Graph Sensor Data Generate Line Equation

Some sensors (such as sonar and Sharp IR) do not work properly at very close range

I will go through the process of making a guitar string physical touch sensor.

pseudocode: read left_photoresistor read right_photoresistor if left_photoresistor detects more light than right_photoresistor then turn robot left if right_photoresistor detects more light than left_photoresistor then turn robot right if right_photoresistor detects about the same as left_photoresistor then robot goes straight loop

Photovore Algorithm, Improved This algorithm does the same as the original, but instead of case-based it works under a more advanced Fuzzy Logic control algorithm. Your robot will no longer just have the three modes of turn left, turn right, and go forward. Instead will have commands like 'turn left by 10 degrees' or 'turn right really fast', and with no additional lines of code! pseudocode: read left_photoresistor read right_photoresistor left_motor = (left_photoresistor - right_photoresistor) * arbitrary_constant right_motor = (right_photoresistor - left_photoresistor) * arbitrary_constant loop

Usually, the operating system takes all the values from the sensors, averages them, then finds the one that is the furthest away from that average

The Ant Farm is built next to a very large window that faces east. As a result, with the lab lights off, the brightest light source is always to the east. The robots can use this as a reference and then find all the other directions.

The Sharp IR Range Finder works by the process of triangulation. A pulse of light (wavelength range of 850nm +/-70nm) is emitted and then reflected back (or not reflected at all). When the light returns it comes back at an angle that is dependent on the distance of the reflecting object. Triangulation works by detecting this reflected beam angle - by knowing the angle, distance can then be determined.

The IR range finder reciever has a special precision lens that transmits the reflected light onto an enclosed linear CCD array based on the triangulation angle.

The Sharp IR has a non-linear output. This means that as the distance increases linearly (by set increments), the analog output increases/decreases non-linearly.

camera-based vision system (for light detection and navigation) two microphones, binaural hearing beat detection (allows pleo to dance and listen to music) - this feature was removed but may be added on again. eight touch sensors (head, chin, shoulders, back, feet) four foot switches (surface detection) fourteen force-feedback sensors, one per joint orientation tilt sensor for body position infrared mouth sensor for object detection into mouth infrared transmit and receive for communication with other Pleos Mini-USB port for online downloads SD card slot for Pleo add-ons infrared detection for external objects 32-bit Atmel ARM 7 microprocessor (main processor for Pleo) 32-bit NXP ARM 7 sub processor (camera system, audio input dedicated processor) four 8-bit processors (low-level motor control)

Pleo Technical Specs: Ugobe LifeOS 32 bit Atmel ARM 7 microprocessor - The main processor for Pleo 16 bit sub processor - The processor dedicated to the camera system (4) 8 bit processors that provide the low-level motor control for the servos (35) Sensors including a camera custom designed to fit into Pleo’s very compact body. (4) foot-switches to detect footfalls and being picked up - assists with spatial orientation. (12) capacitive touch sensors (4) legs, (4) feet, back, shoulder, head, chin (2) microphones for directional sound detection (14) “Force” sensors, one per servo, to recognize abuse through force feedback joints. Orientation/tilt sensor IR transceiver for bidirectional data communication with other Pleos. IR interrupter for detection of objects in Pleo’s mouth (14) motors. Standard low voltage DC motors (150) gears and clutches Rechargeable NiMH battery pack USB port with mini USB connector SD/MMC memory card slot

note that the human body is a good absorber of stray RF fields, so this sensor should be a good people-detector

All of the procedures take a discrete ``gear'' to specify the speed. The reasons for this are two-fold; first, by limiting the power of the truck, we simplify the interface to children. Secondly, it allows use to calibrate the ``gears'' so that, for example, 10 seconds forward in first gear is the same distance as 10 seconds backward in first gear.

The limitation of LOGO however is the lack of feedback from the environment. There is no way of expressing an event occuring in the outside world.

Simple constructs in iLogo extend the original LOGO language with interactivity capabilities of reading sensors and transfering control to different parts of the program.

I wanted to share an adaptation of the Schead v4, that I have been experimenting with. It is (for lack of a better term) a Master/Slave Schmitt Comparitor Head (M/S SC-H). With the addition of a 74 AC 240 or two (as motor drivers) and a pair of motors, you can put together an interesting little light seeking, wheeled robot with peripheral vision.

As long as the light reaching the photo-bridge of the Master SC-H is balanced, then the Slave SC-H acts as a regular, lone SC-H would. So, if one of the slave photo-diodes detects more light then the other, the inverter that controls the motor on that side changes states and is now the same as the inverter of the Master SC-H tied to the same motor. This turns that motor off and the robot will pivot around the stopped wheel toward the greater light source until the light on each sensors is balanced and the motor again begins to turn.

I am also using SCar to continue experimenting with Stacking separate Sensor/Behavior circuits onto a robot. I will post more as progress is made.

All Cricket devices have a built-in bidirectional infrared communications channel, which is used for Cricket-to-desktop communication (when downloading programs to a Cricket, or viewing sensor data) and Cricket-to-Cricket communication.

Cricket Logo is based on an iterative, interactive model of project development. It includes a “command center” window; instructions typed into this window are instantaneously compiled, downloaded to a Cricket, and executed, giving the system the flavor of an interpreted software environment such as LISP, BASIC, or FORTH.

The MetaCricket software system is based on a virtual machine, written in PIC assembly language and running on the Cricket, and a compiler for the virtual machine running on a desktop development computer

The motor is driven in either the forward or reverse direction, but will swap polarity if the motor encounters too sudden or great of a load

CALEB CHUNG: Of course we could have used micro-servo motors to accomplish the motion of Pleo, but we aren’t able to use expensive motors. So we had to engineer it with a high-speed motor with high gearing and no backlash for control purposes and have it all fit within the muscle envelope of Pleo.

So what we did was go after a lot of ethology research. How do animals really handle the complexity of their environment? We built a virtual brain—a whole system that decides how Pleo will react in various situations.

CALEB CHUNG: Pleo will reset thresholds and adjust his idea of what he thinks is normal. Let’s say you get Pleo and you take him home to your shag carpet. When Pleo walks, the carpet will drag on his feet. So his force feedback sensors will realize that he is spending too much energy to walk around. Pleo will try different things to reduce the energy spent. Eventually, he will have the idea to step higher. Your Pleo compared to my Pleo will walk with a higher step.

Note that the resistor value of the pull-down resistor affects the voltage at pin 3 of the Furby's connector. We used a 1k ohm resistor to make it less sensitive to light (since we're now operating with it open to ambient light).

In the above diagram, a 20k ohm resistor is used as the pull-up resistor. You can, however, use any resistor as the pull-up resistor as long as the resistance is high enough to protect the circuit.