Electronic Everything!

The design of a generator system requires many hours of detailed planning with the goal of creating an extremely reliable backup power source. Properly installed, the system will deliver the intended level of reliability. However, if incorrectly wired, the system can become a problem for both the owner and the manufacturer. While the generator installation can be handled by a range of people, from a trained technician to the typical homeowner, wiring mistakes can occur. Installation includes working with 120 VAC split phase, 240 V line voltage, along with low-voltage signals below 50 V. A small and easily made mistake, such as miswiring high voltage to low voltage, will destroy sensitive electronics quickly and may render the equipment inoperable. Thus, a resettable overcurrent and overvoltage solution capable of handling line voltage, electrostatic discharge (ESD), electrical fast transients (EFT), and current surge is required to protect low voltage interface circuits against this problem.

Samplify Systems Inc. (Santa Clara, Calif.) has announced an autofocus beamforming technology for ultrasound imaging. The technology uses a 32-channel ultrasound analog front-end receiver module in an ultra-small small-outline dual-in-line configuration based on the SAM1600 family of compressing ADCs.

Tiny semiconductor dots could lead to a new type of circuit based on magnetism rather than current flow. At least that’s the hope of researchers who’ve made the dots and are hoping to build them into a workable device. ”We want to make it into a so-called nonvolatile transistor,” says Kang Wang, head of the Device Research Laboratory at the University of California, Los Angeles. Such a ”spintronic” transistor would retain its logic state in the absence of current and require less power to switch a bit, reducing the electrical power required by a computer chip by as much as 99 percent. Wang’s research, supported in part by Intel, was published in March in the online version of Nature Materials. Where electronic transistors rely on the presence or absence of current to register the ones and zeros of digital logic, spintronic transistors depend on ”spin,” a quantum characteristic of the electron. Picture the electron as a rotating globe. When the north pole is pointing upward, that’s spin up; when pointing the other way, it’s spin down. When the spins of most electrons are aligned, the material is magnetic. When their spins are random, the material isn’t. An applied current can align or randomize the spins, allowing for spin-based switches.

Related to the strong demands for virtualization technology, network I/O virtualization has recently become a hot topic and is one of the key topics being discussed at the upcoming Multicore Expo @ ESC. In fact, analyst firm IDC, in a recent white paper titled "Optimizing I/O Virtualization: Preparing the Data Center for Next-Generation Applications", stated that "If I/O is not sufficient, then it could limit all the gains brought about by the virtualization process."

LED luminaires require precise power and heat management because LEDs convert most of the electrical energy they receive into heat rather than light. Without adequate thermal management, this heat can degrade the LED's life span and affect color output. Also, LEDs can fail short because they are silicon devices, so they may require fail-safe backup in the form of overcurrent protection. Resettable PPTC (polymeric-positive-temperature-coefficient) circuit-protection devices have demonstrated their effectiveness in a variety of LED-lighting applications. Like traditional fuses, they limit current after they exceed specified limits. However, unlike fuses, PPTC devices can reset after the fault clears and the power cycles.

It’s 2020, and it’s sunny outside. In fact, it’s so bright in your kitchen that you have to squint to see your grapefruit. You flip on your e-reader and the most recent e-issue of IEEE Spectrum pops up on-screen, the colors and text sharp and brilliant in the sunlight. There’s e-mail to answer, but you want to make the early commuter bus, so you roll up your e-reader and stuff it in your jacket pocket.

Experimental microbial fuel cells could turn bacteria into batteries that generate electricity from biomass. The key to this technology is the ability of bacteria to transfer electrons to their surroundings—for example, to the anode of a microbial fuel cell. But if the organisms have to be in direct contact with the anode, such devices would have to have extremely large surface areas. Researchers from Aarhus University, in Denmark, report today in the journal Nature that bacteria appear to conduct electricity while separated by several millimeters, at least a thousand times as far apart than previously demonstrated. The naturally occurring electric currents, if confirmed, would allow bacteria spaced at least 12 millimeters apart to communicate electrically. The discovery might lead to new paths to treating infection and a better understanding of microbial ecosystems.

The race to create tiny wireless sensors that could monitor anything from pressure in the eyes and brain to the stability of bridges appears to be heating up. Earlier this month, IEEE Spectrum reported on two approaches to creating an almost-indefinitely-running sensor using piezoelectric systems to convert tiny vibrations into power. Now, another team from the University of Michigan has created an alternative approach that uses solar power to keep the sensor running autonomously for many years.

Three-dimensional microchip designs are making their way to market to help pack more transistors on a chip as traditional scaling slows down. By stacking logic chips on top of one another other or combining logic chips with memory or RF with logic, chipmakers hope to sidestep Moore's Law, increasing the functionality of smartphones and other gadgets not by shrinking a chip's transistors but the distance between them. "There's a big demand for smaller packages in the consumer market, especially for the footprint of a mobile phone, or for improving the memory bandwidth of your GPU," says Pol Marchal, a principal scientist of 3-D integration at European microelectronics R&D center Imec. On 9 February, at the IEEE International Solid-State Circuits Conference (ISSCC), in San Francisco, Imec engineers presented some key design challenges facing 3-D chips made by stacking layers of silicon circuits using vertical copper interconnects called through-silicon vias (TSVs). These design constraints will have to be dealt with before TSVs can be widely used in advanced microchip architectures, Marchal says.

A little more than a week after long-simmering programmable logic startup Tabula Inc. emerged from stealth mode, Tier Logic Inc. stepped into the light Wednesday (March 10), offering the first details about its technology, which employs a novel processing change to build FPGA and ASIC products on a single die. Like Tabula, Tier Logic's technology depends on a three-dimensional structure. But while Tabula uses rapid reconfiguration to, in the words of that firm's executives, treat time as the third dimension, Tier Logic's approach separates user circuits and configuration circuits into 3-D stacked layers, creating what the company calls the world's first monolithic 3-D FPGA.

This API provides users with a standard FPGA communication interface from C++ code. It is intended to encourage more widespread adoption of FPGAs and reconfigurable computing platforms—particularly among Windows application developers

When considering the resolution required for an A/D converter (ADC) integrated in a microcontroller (MCU), embedded systems designers must balance cost and performance. Higher ADC resolution implies higher-cost MCUs, but in some cases you can use other features in the MCU to enhance the ADC performance via software. That approach lets you achieve higher resolution using an inexpensive integrated ADC. Here's how to use of oversampling to achieve extra bits of resolution for an ADC integrated in an MCU.

In a recent video, Willow Garage researcher Eitan Marder-Eppstein describes the open-source navigation stack they've released as version 1.0. The code, available at http://ros.org/wiki/navigation, was designed to be flexible and cross-platform, he says, and could be used in anything from a small iRobot Create-based bot to a large multi-sensor robot like Willow's own PR2 (which Spectrum has covered in detail here and here).

A product can be of low quality for several reasons, such as it was shoddily manufactured, its components were improperly designed, its architecture was poorly conceived, and the product's requirements were poorly understood. Quality must be designed in. You can't test out enough bugs to deliver a high-quality product. The quality assurance (QA) process is vital for the delivery of a satisfactory system. In this last part in this series, we will concentrate on portions of the methodology particularly aimed at improving the quality of the resulting system. The software testing techniques described earlier in this series constitute one component of quality assurance, but the pursuit of quality extends throughout the design flow. For example, settling on the proper requirements and specification cannot be overlooked as an important determinant of quality. If the system is too difficult to design, it will probably be difficult to keep it working properly.

Just as photographic film was mostly replaced by silicon image chips, now quantum film threats to replace the conventional CMOS image sensors in digital cameras. Made from materials similar to conventional film—a polymer with embedded particles—instead of silver grains like photographic film the embedded particles are quantum dots. Quantum films can image scenes with more pixel resolution, according to their inventors, InVisage Inc., offering four-times better sensitivity for ultra-high resolution sensors that are cheaper to manufacture.

25 March 2010—Nowadays, a phone that doesn’t know where it is or where it’s going can’t really call itself ”smart.” To orient themselves properly, smartphones require not just GPS capability but also an electronic compass, an accelerometer, and increasingly, digital gyroscopes. The point of a gyroscope is to sense any change in an object’s axis of rotation. Up until now, gyroscopes measured movement around the three axes with three sensors—one for pitch, one for yaw, and another for roll. At most, two of these sensors would be combined on a single die. The best you could do was, say, match up a 3- by 5- by 1-millimeter yaw sensor with a 4- by 5- by 1-mm sensor that would detect pitch and roll. But on 15 February, STMicroelectronics unveiled  a 4- by 4- by 1-mm gyroscope whose single sensing structure tracks all three angular motions. It’s a triumph of microelectromechanical systems (MEMS) engineering.

I remember when, a decade ago, Kevin Warwick, a professor at the University of Reading, in the U.K., implanted a radio chip in his own arm. The feat caused quite a stir. The implant allowed him to operate doors, lights, and computers without touching anything. On a second version of the project he could even control an electric wheelchair and produce artificial sensations in his brain using the implanted chip. Warwick had become, in his own words, a cyborg. The idea of a cyborg -- a human-machine hybrid -- is common in science fiction and although the term dates back to the 1960s it still generates a lot of curiosity. I often hear people asking, When will we become cyborgs? When will humans and machines merge? Although some researchers might have specific time frames in mind, I think a better answer is: It's already happening. When we look back at the history of technology, we tend to see distinct periods -- before the PC and after the PC, before the Internet and after the Internet, and so forth -- but in reality most technological advances unfold slowly and gradually. That's particularly true with the technologies that are allowing us to modify and enhance our bodies.

The FPGAs referenced in these articles have complex dedicated I/O circuitries that are primarily designed to support external memory interfaces. The ALTMEMPHY megafunction is designed to support the most common memory standards, such as the DDR and DDR 2 SDRAM and QDR II+/QDR II SRAM (in a burst length of 4) interfaces. The ALTMEMPHY megafunction should be used whenever possible as it is beneficial to use the IP and timing closure methodologies used with these FPGAs, which enables users not to have to create this function manually as compared with using the ALTDLL and ALTDQ_DQS solution. However, the ALTMEMPHY megafunction does not support other external memory standards such as Mobile DDR, QDR II+/QDR II SRAM (in burst length of 2) or customized DDR and DDR 2 SDRAM external memory standards. For these scenarios, use the ALTDLL and ALTDQ_DQS megafunctions to access the FPGA architecture and build a custom external memory interface.

FPGAs referenced in this article have complex dedicated I/O circuitries that are primarily designed to support EMIF. The ALTMEMPHY megafunction is designed to support the most common memory standards, such as the DDR , DDR2 SDRAM, and QDR II+/QDR II SRAM (in a burst length of 4) interfaces. Other external memory standards such as Mobile DDR, QDR II+/QDR II SRAM (in burst length of 2), or customized DDR and DDR 2 SDRAM external memory standards are not supported. Instead, the ALTDLL and ALTDQ_DQS megafunctions are used to access the FPGA architecture and build a custom EMIF.