Group items tagged

Analog Devices, Inc., has introduced a pair of Class-D audio amplifiers for smart phones, GPS units and other handheld electronics where premium sound quality offers a major competitive advantage. The SSM2375 and SSM2380 amplifiers provide audio system designers with the option of fixed or programmable gain settings combined with low noise and superior audio performance. The SSM2380 low-power, stereo Class-D amplifier is the first in its class to incorporate an I²C interface, which allows gain stages to be set from 1 dB to 24 dB (plus mute) in 47 distinct steps with no other external components required. The programmable interface also enables independent L/R channel shutdown, a variable low-EMI (electro-magnetic interference) emission control mode, and programmable ALC (automatic level control) functions for speaker protection. The SSM2380 achieves a 100-dB SNR (signal-to-noise ratio) and extends battery life by achieving 93 percent power efficiency at 5 V while running at 1.4 W into an 8-ohm speaker.

Synopsys, Inc., has unveiled the DesignWare Ethernet Quality-of-Service (QoS) Controller IP which implements the new IEEE specifications for audio video bridging (AVB) features. The DesignWare Ethernet IP solution supports the new IEEE 802.1AS and 802.1-Qav version D6.0 specifications. These specifications enable efficient networking of streaming audio video (AV) applications through IEEE 802.1 networks found in consumer electronics, automotive AV and professional sound system products. Synopsys' DesignWare Ethernet QoS Controller, which supports 10/100/1G data transfer speeds, allows designers to develop system-on-chips (SoCs) that deliver time-synchronized, low-latency audio and video over Ethernet networks with exceptional quality-of-service while retaining compatibility with legacy networks.

In high-end audio equipment, careful selection of resistors is one of the best ways to avoid or minimize noise and distortion in the signal path. This paper describes the noise generation in resistors manufactured using the various available resistor technologies and quantifies the noise insertion typical for each type.

Field programmable gate arrays (FPGAs) present an efficient and inexpensive alternative when it comes to implementing complete embedded systems along with important peripheral functions. The reconfigurable logic circuitry of an FPGA offers tremendous flexibility. A lesser known feature is that the outputs of a digital FPGA also permit various analogue applications.

NXP BV (Eindhoven, The Netherlands) has said it will demonstrate a microcontroller based on the ARM Cortex-M4 at the Embedded Systems Conference in San Jose, California. NXP was one of the first companies to license the Cortex-M4 processor core and a chip has been implemented using a low-leakage 90-nm process technology. This enables performance in excess of 150-MHz clock frequency, NXP said. NXP has added proprietary power-down techniques to reduce power consumption. The ESC Silicon Valley demo will show that a 7-channel audio graphic equalizer application processing 32-bit precision audio data requires only 12 MHz of CPU bandwidth using the Cortex-M4 DSP extensions, and 60 MIPs without. The core includes DSP extensions not usually found inside a microcontroller and NXP's implementation are aimed at a broad set of applications including motor control, digital power control and embedded audio.

When considering the resolution required for an A/D converter (ADC) integrated in a microcontroller (MCU), embedded systems designers must balance cost and performance. Higher ADC resolution implies higher-cost MCUs, but in some cases you can use other features in the MCU to enhance the ADC performance via software. That approach lets you achieve higher resolution using an inexpensive integrated ADC. Here's how to use of oversampling to achieve extra bits of resolution for an ADC integrated in an MCU.

Given the maturity of MOSFETs, selecting one for your next design may seem deceptively simple. Engineers are familiar with the figures of merit on a MOSFET data sheet. Selecting a MOSFET requires the engineer to use their expertise in scrutinizing different specifications for individual applications. In an application such as a load switch in a server power supply, the switching aspects of a MOSFET matter little because the MOSFET is on almost 100% of the time. The on resistance (RDS(ON)) may be the key figure of merit in such an application. Still other applications, including switching power supplies, use MOSFETs as active switches, and cause the engineer to value other MOSFET performance parameters. Let us consider some applications and their prioritization of MOSFET specifications.

The ARM Cortex™-M4 processor is the latest embedded processor by ARM specifically developed to address digital signal control markets that demand an efficient, easy-to-use blend of control and signal processing capabilities. The combination of high-efficiency signal processing functionality with the low-power, low cost and ease-of-use benefits of the Cortex-M family of processors is designed to satisfy the emerging category of flexible solutions specifically targeting the motor control, automotive, power management, embedded audio and industrial automation markets. The Cortex-M4 processor features extended single-cycle multiply-accumulate (MAC) instructions, optimized SIMD arithmetic, saturating arithmetic instructions and an optional single precision Floating Point Unit (FPU). These features build upon the innovative technology that characterizes the ARM Cortex-M series processors…

Verification of algorithm-intensive systems is a long, costly process. Studies show that the majority of flaws in embedded systems are introduced at the specification stage, but are not detected until late in the development process. These flaws are the dominant cause of project delays and a major contributor to engineering costs. For algorithm-intensive systems —including systems with communications, audio, video, imaging, and navigation functions— these delays and costs are exploding as system complexity increases. It doesn't have to be this way. Many designers of algorithm-intensive systems already have the tools they need to get verification under control. Engineers can use these same tools to build system models that help them find and correct problems earlier in the development process. This can not only reduce verification time, but also improves the performance of their designs. In this article, we'll explain three practical approaches to early verification that make this possible. First, let's examine why the current algorithm verification process is inefficient and error-prone. In a typical workflow, designs start with algorithm developers, who pass the design to hardware and software teams using specification documents.

The consumer handheld market is growing by leaps and bounds. With more processing power and increased support for more applications, portable products are cross-pollinating with traditional computing systems even as the product life cycle has decreased considerably in this market segment. As a result, especially in this era of economic slowdown, it is imperative that new products meet the time-to-market window to gain maximum acceptance. A decrease in product life cycles requires a reduced development cycle and an increased emphasis on reusability and reprogrammability. The emerging handheld market is also seeing interesting trends in which each individual device in a family has lower volumes but there is more customization across the series of devices, effectively upping the total unit volumes. The key challenge then becomes how to develop a system that is widely reusable and also customizable. These requirements have led designers increasingly to turn to the FPGA for handheld-product development. The FPGA has become more powerful and feature-rich, while gate counts, area and frequency have increased. FPGA development and turnaround cycles are considerably shorter than those of custom ASICs, and the added advantage of reprogrammability can make the FPGA a more compelling solution for handheld embedded systems.

Intel has announced that is developing a system-on-chip for embedded applications based around its Atom processor core. However, it appears the SoC will be of a fixed design with a PCI Express bus interface to which system-level customers can attach their own or third-party chips. Similarly it appears that Intel will manufacture the system-chip internally rather than allowing a foundry to make the chip, or add its customers' IP to the design. Doug Davis, corporate vice president and general manager of Intel's embedded and communications group, disclosed details of the "Tunnel Creek" SoC during his keynote speech on Wednesday (April 14) at the Intel Developer Forum, in Beijing China.