Group items tagged

I read an interesting article today about safety by Mari-len De Guzman on Cos-Mag.com, an occupational safety e-magazine for Canadian manufacturers. At the CSSE (or, Canadian Society of Safety Engineering) conference in Niagara Falls this week, Los Alamos National Laboratory safety expert, Todd Conklin, spoke about how many manufacturing and industrial companies look at safety issues. He pointed out that, rather than continually blame operator-error for most failures and safety problems, it is more systemic, stating that: workers get hurt when they find themselves in situations where it's hard to be safe and easy to get hurt. With that in mind, he offered several potential causes for failure or safety incidents and ways to combat them. First, he said that humans make mistakes, so he advised that it is important to anticipate those potential mistakes and have several levels of defensive safety measures. Next, he suggested that companies should anticipate that unforeseeable events can happen, and WILL happen, so employers and safety managers need to keep this in mind. Learning is another tip Conklin pointed out. Whenever something bad happens, the best defense next time is to learn as much as we can from the event. We can learn many things, like defenses, unsafe speeds, too much load, proximity to dangerous equipment or products, etc. Finally, he also advised managers to approach safety or failure issues (and the operators involved) with caution. He warned that being positive and asking things in a proactive manner can give a much better reply or response, as follows: Instead of asking a worker, "what have you done, now?" ask them, "how do we set this up so failure doesn't happen again." By asking the right question, employers can get a more operational-centric answer. I really thought this was great info. It might seem like common sense to some, safety matters and needs to be one step ahead of the production line. I also more or less agree with Con

Since the inception of factory production in the industrial revolution, safety has been a concern. However, safety today looks nothing like it did back then. We now have OSHA and other government groups, unions, and lobbies that safeguard the safety of workers and make sure that they are adequately provided for. In addition, workers themselves have more rights in suing an employer over unsafe conditions and receiving compensation in the event of an incident that leaves them injured. Especially if an injury prevents them from providing for their family. The point is, a lot has changed over the past few hundred years in workplace safety, and those changes have unanimously been in the best interests of the workers that inhabit those workplaces. However, just as changing times caused safety evolution in the past, it is important that this trend continues now with the advent of things such as the internet, tablets, smart phones, and more. Safety is no longer limited to physical seminars and training sessions. That being said, let's take a look at exactly how you can use technology and engagement to enhance your safety efforts. eNewsletter to Employees One way that employers are reaching their employees both in a new way and outside of the physical confines of the work area is through email newsletters. The vast majority of working adults (and most every demographic, for that matter) are online these days and employers need to make sure they are taking advantage of that online time and platform. Formatting an email newsletter is great because it can be easily sent out to every single employee in your workforce. This can be used for general company news and the like, but can also be used to send out weekly safety lessons or reminders for employees about any witnessed unsafe behavior. To get started down this round, you'll need to make sure your emails get opened and engaged with. Here are a couple of ways to do that: 1. Keep your subject lines short but catchy. Sub

Waste water treatment plants are usually operated by municipalities or private utility companies, and are regulated by the states wherein they reside, but their standards were enacted by the U.S. Environmental Protection Agency (EPA). According to the Safe Drinking Water Act of 1974 (amended in 1986 and 1996), all local treatment systems are regulated so that the water they treat is tested for contamination, their improvement plans are reviewed, they have onsite inspection to ensure that machinery and sanitation efforts are functioning properly, that personnel are properly trained, and that they comply with all standards (or face stiff penalties). On top of these regulations are safety expectations imposed by the Occupational Health and Safety Administration (OSHA) under the U.S. Department of Labor. Waste water treatment plants have so many potentially hazardous areas that can impact people, directly and indirectly. Who is Affected? Directly, employees at the plant run the risk of workplace injuries from working around the huge pumps, walking near and above open water treatment containment tanks, agitator pools, furnaces, pipes, and various other facility obstacles, machinery and equipment which can create pitfalls for unsuspecting workers. Indirectly, end users of the treated water run the risk of drinking and using improperly treated water, but this post is primarily concerned with the safety of workers and visitors to the treatment plant. Ways to Make It Safe Pump pipe marking label image from wikipedia Workers who must work near open vats of raw sewage or even treated water should have all opportunities for falling into the water prevented via various safety devices, warning signs, or precautions. Potentially hazardous holding tanks or agitators should have traction tape laid on walkways or catwalks to reduce slipping. All pipes should be clearly marked with pipe marking labels to display what the contents of the pipes are. Any electric panels should b

In the video below, we take a GoPro camera ride along with a tower climber as he scales to the top of a 1768 foot tall antenna. The worker slowly climbs on increasingly smaller and precarious looking ladder rungs, all while toting a 30 pound tool bag behind him, occasionally assisted by his climbing partner. The video, aptly titled "The most dangerous job in the world," is stirring up a lot of controversy, especially because it has simply shed light on a profession most people didn't even know existed. Tower climbers are often hired by cell phone companies to adjust antennas and mechanisms located at the top of their cell towers; they are often required to climb thousands of feet into the air. However, the even scarier part is that in many cases, they do not even use any sort of safety cable. In the video, a voice over remarks that OSHA regulations allow for this type of "free climbing" method. As it turns out, most experts are confused as to where the video makers got that idea, as there's nothing to be found in the OSHA guidelines that condones such procedure. In fact, to the contrary, OSHA has published findings highlighting the lethality of this particular profession and method, noting that AT&T alone has had 15 cell tower workers die from falls since data started being collected in 2003. What's even worse is that sanctions against cell companies have been nearly non-existent, and not once has OSHA gone after the larger providers, despite their high mortality rates. Part of this may be due to a loophole (indeed perhaps the very same one that the video cites as "allowing" for such a dangerous climb) that won't hold companies liable for the unsafe behavior of independent contractors if they don't have knowledge of it. In short, a contractor, knowing full well their workers will be free climbing, can simply not communicate to a cell company as such which in turn gives them plausible deniability. Why Should You Care As A Business Owner? ​No

The pertinent use of safety stickers and labels is a must within any industrial work environment. Safety stickers and labels serve many functions, first and foremost, they help to warn or inform employees and visitors of any specific safety concerns. Additionally, they also serve as handy informational reminders from identifying the contents within certain pipes, to showing where recycling may be located, all the way to highlighting the location of a safety eye wash station. Since the need for safety stickers is so important, yet so diverse depending upon the type of business, it may be difficult to locate all the specific stickers and labels needed. One way to easily combat the rising costs of utilizing outside retailers for safety stickers is to simply make your own. Believe it or not, printing your own safety stickers is generally faster, easier, and more cost efficient. Printing Safety Stickers If you've never considered the option of printing your own safety stickers, right now is the time to start. With advances in technology, some label printers are able to efficiently print bright and colorful, commercial grade stickers and labels. One label printing product currently on the market that rivals most others in price, quality, and ease of use is the LabelTac 4 PRO. This printer has proven time and time again to produce high-quality, dependable, colorfast labels that outperform most other safety stickers available on the market, and the best part is they can be printed in-house right from your own office. The LabelTac 4 PRO is capable of creating indoor and outdoor labels that are both weather and fade resistant. Furthermore, the ease of use with the LabelTac 4 PRO is simply impressive to say the least. It is compatible with nearly any Windows-based programs including well-known products such as Microsoft Office, OpenOffice, and Excel. However, even if you don't utilize Windows-based software the LabelTac 4 PRO comes equipped with its own easy-to-use Barte

Safety in foreign countries is way below the standards of the USA, but you can actually find the they exact same problem of wiring and code violations maybe even in your own house or work. As may works cut corners in the hope to speed up the project not really caring about the purchaser. It is very disheartening that in spite of several laws, codes and stipulations by the government, we are witnessing so many accidents. The need of the hour is to spread safety awareness so as to instil confidence in people that the government is very clear about enforcing all laws and regulations to avoid accidents. The main focus areas are homes, where gadgets like LPG stoves, induction heaters and microwave ovens, if not used safely, could lead to serious accidents. The international precautionary indication is that LPG is strongly blended with smelling agents so that leaks are detected, but due to a lack of knowledge and awareness, timely action is not taken, resulting in nasty accidents and loss of lives. Use of substandard electrical wires and switches, inserting wires into sockets without plugs and improper earthing are the main reasons for accidents due to electricity. It is advisable to use appliances of standard makes and which are BIS marked. The placing of air conditioners in the correct positions and using non-flammable switch boxes would avoid mishaps. The use of ELCBS and flame-proof wiring will assure us of safety from electric shocks at homes. Safety audits Safety in schools is of primary importance. Playground equipment, swimming pools, auditoriums and laboratories are to be professionally managed. Periodic inspections and safety audits are to be conducted by accredited third parties and the reports communicated to parents so as to reassure them that their children are in a safe atmosphere. Lab equipment and hazardous chemicals are to be handled after thorough training. Vehicular traffic involving children has to be monitored closely. Safety levels in hospitals are