project of circuit potency lineal RF amplifier with BLY90 for Fm transmitter or vhf transmitter Circuit for lineal amplifier for VHF with power source and printed circuit board, using the transistor Bly90
It is to be used as amplifier of potency of RF in the high strip of of the power source that should be capable to supply a tension of 13 volts with a current of 10 amperes. it demands right care in the assembly of the source. Terrified armored transformer, and three shocks of RF to filter the components of high frequency.
XRF1 and XRF2 are 30 you turns of wire 25 AWG in a nucleus of ferrite of 1 cm of diameter and 5 cm length. It can use one of a source at/atx bad, it is easier. XRF3 are 100 you turns of wire 25 AWG in a ferrite nucleus and 1cm of diameter for 5cm of length. Or use an usually found in the exits of sources ATX’s. something around 100µH. The capacitors C1, C2, C3, C4 should be ceramic of 600 V or more and the capacitors of 10nF are for 100v. RX cannot be of wire. Power supply circuit for the rf lineal amplifier Orijinal görüntüsünü görmek için buraya tıklayın. 512x223 px. About the transistor BLY90
The Transistor BLY90 was developed to work in the classes THE, B and C, with 12.5V current of 8A. For applications above 175MHZ. Below we have the diagram circuit of the amplifier using an only transistor BLY90. All capacitors should be ceramic. The resistor of 10Ω for 1 w should not be of wire, the entrance impedance and exit is of 50Ω , soon it should be linked with cable of 50Ω . It should be observed the legal restrictions as the operation of that equipment type. Diagram circuit of the project for the rf lineal amplifier Orijinal görüntüsünü görmek için buraya tıklayın. 522x297 px. Printed circuit board for the lineal amplifier with bly90
Below we have the drawing of the printed circuit board of the transmitter, observe that the components are mounted beside the copper and with the terminals the shortest possible, use heatsink in BLY90. lists of material for assembly of the lineal RF potency amplifier Power Supply RX = 22KΩ 1W C1,C2,C3,C4 = 100nF 600V Ceramic C5,C6,C7,C8, =10NF 100V C9 = 100NF C10 = 4700µF C11 = 2200µF D1,D2,D3,D4 = 1N5401 or equivalent. XRF1,XRF2 = 30 turns of wire 25 AWG in nucleus of ferrite of 1cm diameter for 5 length. Optional, use a shock of RF of a computer source, those of the entrance of the net. XRF3 = 100 turns of wire 25 AWG in a nucleus of ferrite of 1 x 5. T1 = Transformer of 12 Volts for 10 Ámperes with screening. Several = box, plugs, cables, etc. Amplifier of RF Q = BLY90 R = 10Ω 2W C1 =15PF C2,C3,C4,C5 = 100PF C6 = 470NF C7,C10,C11 = 470PF C8 = 47PF C9 = 56PF C12 = 22PF CV1,CV2 = TRIMMER 4 – 40PF CV3,CV4 = TRIMMER 60PF MAX. L1 = 3 turns of wire 24 AWG with diameter of 7mm, nucleus of air. L2 = Shock of RF of 0.22µH. L3 = 15 turns of wire 24 AWG around a resistor of 47Ω x 2W (it doesn’t serve as wire) L4 = 3 turns of wire 24 AWG with diameter of 7 mm, nucleus of air. L5 = 1 turns (sees fig. below for details) L6 = 3 turns of wire 24 AWG with diameter of 7 mm., nucleus of air. L7 = 4 turns of wire 24 AWG with diameter of 7mm, nucleus of air. Several = printed circuit board, antenna, cables, heatsink, box, etc. Detail of L5. That project is just for ends of didactic test, that doesn’t implicate in any responsibility of the idealizator about the non operation or illegality of operation of the equipment.
Ahmet UZUN on 18 Mar 12" Precision Power Supply © 1986 Doug Bedrosian and 2010 Tony van Roon "This Precision Power Supply is a nice addition on your workbench as primary, or in my case, a supplementary power supply. With zero to 40V and 2A with adjustable current limiting it will surely gets lots of use on your bench. On average the most amperage for a power supply someone needs is around two or three amps. The sensitivity for current limiting is fully adjustable. Have fun building!" Introduction: Test instruments are considered to be some of the most useful tools available when constructing a project. They are also considered to be the most expensive tools one could buy. For instance, a power supply of any quality and usefulness can range from several hundred dollars to several thousand dollars. The alternative to buying a power supply is to build one. The power supply in this article has a voltage range from 0 to 40V and a current range from 0 to 2 amps with current limiting set by the user. The quality of the supply is determined by the time and care the builder takes while constructing it. How It Works: The power supply is best understood when divided into separate parts. The first parts to look at are the two power supply sections. The output supply section consists of XFMR1, Br1, C1, and C2. They supply the appropriate voltage and current required at the output. The IC supply consists of XFMR2, Br2, and C3. The two power supply sections must be separate from each other because a floating ground is required for IC1. The next section is the voltage control. RV1 and R2 determine the operating point of a constant current source out of pin 3 of IC1. By varying RV1 the maximum output voltage will be set. Pins 8 and 9 are inputs to a high gain differential amplifier contained in IC1. By adjusting potentiometer P1 the voltage at pin 8 will vary; this will cause the voltage at the output to change until it is equal to the voltage at pin 8. Due to the high gain of the differenti
Cached