Glass edging machine as the necessary machinery for deep processing of glass, in appearance is also relatively large, then the price of the edging machine is relatively high. The price on the market is more or less the same, but due to last year's glass off-season not off market, so that the glass edge edging machine also get further development.
Now, share with you the details about the purchase of the edge edging machine, where you should start to observe and review the quality of the edging machine is reliable.
First of all, let us review the basic structure of the edging machine, the host, in and out of the material end guide, glass support frame, floor water tank these four are its basic components. And the host can be divided into the front beam, rear beam, base, column, motor, electrical box, edging wheel water tank.
In this way, it is very clear where the quality inspection of the used edge edging machine before purchase should start. The standard quality requirements, the need for the front beam and rear beam must be flat, and need to have the performance of wear and heat resistance and oxidation, so that the used edge edging machine in the process of high temperature work is not deformed. And, as the base of the edging machine weight bearing, also need to have the same performance as the front and rear beams to ensure the quality of glass edging edge. At the same time, the used edge edging machine requirements for the edging head is higher, the quality of the edging head directly affects the quality of the glass after deep processing.
After years of experience in repair and maintenance, in the purchase of used edge edging machine is the need to pay special attention to the various parts, especially wear-resistant and oxygen-resistant performance requirements of the parts need to be casting parts, welding parts need to be particularly good steel, in order to make the used edge edging machine in the long-term use of the process does not appear major failures, no parts separation, loose, etc..
Finally, the need to pay special attention to the motor piece. The motor with high precision of shaft runout and strong water resistance can better ensure the quality of glass deep processing. The thickness of the motor edging plate and the quality of the motor itself belongs to the bundle effect, the thick edging plate is much higher in cost than the thin plate, so you need to pay attention to check. It is recommended to buy motors made of copper wire, with better bearings and high waterproof performance.
Glass edging machine as the necessary machinery for deep processing of glass, in appearance is also relatively large, then the price of the edging machine is relatively high. The price on the market is more or less the same, but due to last year's glass off-season not off market, so that the glass edge edging machine also get further development.
Now, share with you the details about the purchase of the edge edging machine, where you should start to observe and review the quality of the edging machine is reliable.
First of all, let us review the basic structure of the edging machine, the host, in and out of the material end guide, glass support frame, floor water tank these four are its basic components. And the host can be divided into the front beam, rear beam, base, column, motor, electrical box, edging wheel water tank.
In this way, it is very clear where the quality inspection of the used edge edging machine before purchase should start. The standard quality requirements, the need for the front beam and rear beam must be flat, and need to have the performance of wear and heat resistance and oxidation, so that the used edge edging machine in the process of high temperature work is not deformed. And, as the base of the edging machine weight bearing, also need to have the same performance as the front and rear beams to ensure the quality of glass edging edge. At the same time, the used edge edging machine requirements for the edging head is higher, the quality of the edging head directly affects the quality of the glass after deep processing.
After years of experience in repair and maintenance, in the purchase of used edge edging machine is the need to pay special attention to the various parts, especially wear-resistant and oxygen-resistant performance requirements of the parts need to be casting parts, welding parts need to be particularly good steel, in order to make the used edge edging machine in the long-term use of the process does not appear major failures, no parts separation, loose, etc..
Finally, the need to pay special attention to the motor piece. The motor with high precision of shaft runout and strong water resistance can better ensure the quality of glass deep processing. The thickness of the motor edging plate and the quality of the motor itself belongs to the bundle effect, the thick edging plate is much higher in cost than the thin plate, so you need to pay attention to check. It is recommended to buy motors made of copper wire, with better bearings and high waterproof performance.