Skip to main content

Home/ Groups/ Robotics P1
Rss Feed
Sort By: Most Recent | Popular Filter: All | Bookmarks | Topics Simple Middle
5More

Something to use - 6 views

www.youtube.com/watch
shared by Thomas Helm on 03 Apr 12 - No Cached
  • Thomas Helm on 03 Apr 12
     
    This is im pretty sure everything we have
  • ...2 more comments...
  • Alexander Laferriere on 05 Apr 12
     
    i think that this is a great idea
  • Declan Coen on 05 Apr 12
     
    this would probably work very well and if we added a touch sensor *i dont know if they had one* which would activate the ultrasonic sensor and it would search and pick a path
  • Thomas Helm on 05 Apr 12
     
    That was a good idea declan thanks buddy
  • Declan Coen on 05 Apr 12
     
    OK 0_0
2More

Light sensor and Ultrasonic thats it - 4 views

www.youtube.com/watch
shared by Thomas Helm on 03 Apr 12 - No Cached
  • Declan Coen on 05 Apr 12
     
    this could work but what if the robot turned and started going the wrong direction back towards the start???? it only follows the walls which could lead the robot back to the start not the finish
  • Thomas Helm on 05 Apr 12
     
    anyrobot we do is basically going to be folllowing the wall though and it would have to go all the way to the end to start going back to the beginning
1More

NXT Tutorial - 2 views

www.ortop.org/NXT_Tutorial
shared by Jarid Brogan on 02 Apr 12 - Cached
  • Jarid Brogan on 02 Apr 12
     
    This tutorial is divided into two sections selected on the left. The "Essentials" are things every NXT programmer should know. Some of these movies have exercises directly under them. It's important to do these exercises, not just assume you "get it."
3More

LEGO.com MINDSTORMS : Community : NXTLOG - 4 views

us.mindstorms.lego.com/...DisplayProject.aspx sensor
shared by Bryan Kelleher on 02 Apr 12 - No Cached
  • Bryan Kelleher on 02 Apr 12
     
    the way the ultra sonic sensor is set up is a good idea
  • Thaddeus McKeon on 02 Apr 12
     
    I feel the way they set up the light sensor is a little to far out
  • Joshua Wilkinson on 02 Apr 12
     
    we are gonna have to place the ultrasound or light sensor under three inches if we are following the inside walls, but thats an individule decsion. we could use a code similar to the wall following code in the romba project.
2More

LabVIEW Add-ons for LEGO® MINDSTORMS® NXT - Developer Zone - National Instrum... - 5 views

zone.ni.com/...4435
shared by Thomas Helm on 13 Oct 11 - Cached
    • Alexander Laferriere
      Alexander Laferriere on 13 Oct 11
       
      this shows how to turn on a motor if the button is pressed so if it is not pressed it will stop
  • Thomas Helm on 05 Apr 12
     
    LabVIEW Toolkit for LEGO MINDSTORMS NXT Program and control NXT devices with the full power of LabVIEW Get real-time updates from the NXT device during program operation with LabVIEW front panels Create native blocks for LEGO MINDSTORMS NXT software Figure 1.
3More

How to Solve a Maze - 3 views

www.teamofmonkeys.com/...how2solvemazes.html
shared by Anthony DiVirgilio on 02 Apr 12 - No Cached
  • Wall follower Method:
    • Anthony DiVirgilio
      Anthony DiVirgilio on 02 Apr 12
       
      this would probably be consistant
  • Thomas Corcoran on 02 Apr 12
     
    good techniques for mazes
3More

Single Sensor « The Roboticist - 4 views

www.theroboticist.org/...single-sensor
shared by Andrew Drogan on 12 Mar 12 - No Cached
  • Andrew Drogan on 12 Mar 12
     
    In this setup, a single light sensor is positioned on the robot and programmed to follow the outer-edge of a black line. We commonly refer to the robot executing a 'Z' pattern while following the black line.
  • Thomas Helm on 12 Mar 12
     
    a z pattern might not b the best idea on this because we have a certain time we have to do
  • Declan Coen on 12 Mar 12
     
    if we keep it between a very specific max and minimum then it will not zig zag as much and will appear to go straight
6More

NXT Line Follower - 2 views

www.nxtprograms.com/...steps.html
shared by Joshua Wilkinson on 12 Mar 12 - No Cached
  • When line following, the robot will try to align itself centered over the boundary between white and black (not centered over the black line), with black to the robot's left.  Here the brightness seen by the sensor is halfway between the black/min and white/max readings
    • Joshua Wilkinson
      Joshua Wilkinson on 12 Mar 12
       
      This would be useful since we get the value when its over the tape and table, we can also find the value of the sensor when its directly over the tape then the table seperately.
  • When prompted to sample the "Min" or "Black" reading, position the sensor so that the red spot is centered over the line and then press the Enter button on the NXT. When prompted to sample the "Max" or "White" reading, position the sensor so that the red spot is completely over the surface away from the line and press the Enter button on the NXT.
  • Andrew Drogan on 12 Mar 12
     
    Before line following using either the LineFollow2 or LineFollow5 program, you should "calibrate" the light sensor to the actual conditions expected. With the sensor mounted on the robot where it will be used, and the robot placed over the actual line it will be following, a calibration process takes two light sensor readings, one directly over the line (minimum = darkest), and one over the surface away from the line (maximum = brightest).
  • Declan Coen on 12 Mar 12
     
    if we follow the edge of the line we will always be between the max and the minimum values. therefore, it can detect both values and stay between the min and the max.
  • Thomas Helm on 12 Mar 12
     
    we have to figure out how to correctly calibrate the sensors
11More

PID Controller For Lego Mindstorms Robots - 7 views

www.inpharmix.com/...or_Lego_Mindstorms_Robots.html pid nxt
shared by Declan Coen on 12 Mar 12 - Cached
  • light sensor "sees white" then we know it is left of the line's edge (and the line). If it "sees black" then we know it is to the right of the line's edge (and on the line). This is called a "left hand line follower" since it is following the line's left edge
  • We need to know what values the light sensor returns when it "sees white" and when it "sees black". A typical uncalibrated sensor might give a "white" reading of 50 and a "black" reading of 40 (uncalibrated, on a 0 to 100 scale). It is convenient to draw the values on a simple number line to help visualize how we convert light sensor values into changes in the robot's movement.
  • Below are our made up light values for white and black.
  • ...4 more annotations...
  • We'll just divide the range into two equal pieces and say that if the light level is less than 45 we want the robot to turn left. If it is greater than 45 we want to turn right. I won't go into how exactly the turns should be done. I'll just say that gentle turns work well for a fairly straight line
  • line with lots of curves usually needs to be making sharper turns. For gentle turns you might use Power levels of 50% on the fast wheel and 20% on the slow wheel. For sharper turns on a curvy line you might need to use 30% power for the fast wheel and coast or brake the slow wheel. Whatever power levels you use the numbers will be the same for the two turns, you just switch which motor gets the big number and which get the smaller number (or a stop command).
  • This type of a line follower will follow a line but it isn't very pretty. It looks OK on a straight line with with the motors programmed for gentle turns. But if the line has any curves then you have tell the robot to use sharper turns to follow line. That makes the robot swing back and forth across the line. The robot only "knows" how to do two things; turn left and turn right. This approach can be made to work but it is not very fast or accurate and looks terrible.
  • In the above approach the robot never drives straight, even if it is perfectly aligned with line's edge and the line is straight. That doesn't seem very efficient does it? Lets try to fix that. Instead of dividing our light value number line into two regions lets divide it into three.
  • Anthony DiVirgilio on 12 Mar 12
     
    seems useful for following a line effectively
  • ...1 more comment...
  • Thomas Corcoran on 12 Mar 12
     
    this is a really good technique
  • Declan Coen on 12 Mar 12
     
    the top of this article explains how it would be easier to follow the edge of the line rather than the center of the line. As it detects the white it will turn back to the black and as it detects the black it will turn back to the white.
  • Thomas Helm on 12 Mar 12
     
    i found the edge thing on another site too
2More

Lesson on how to follow the line - 3 views

www.comp.dit.ie/...Sensing_LineTracking.pdf
shared by Andrew Drogan on 12 Mar 12 - No Cached
  • Thomas Corcoran on 12 Mar 12
     
    this gives you a good strategy to find the line after you fall off
  • Andrew Drogan on 12 Mar 12
     
    This lesson will help you to follow the line better and more efficiently
2More

electricbricks » Line Follower in LabVIEW. State Machines - electricbricks - ... - 6 views

blog.electricbricks.com/...lineas-labview-maquinas-estado line follower
shared by Declan Coen on 08 Mar 12 - No Cached
  • Declan Coen on 08 Mar 12
     
    this is a possible way we can program the line folllower excluding the ultrasonic sensor
  • Thomas Corcoran on 12 Mar 12
     
    you can use the ultra sonic sensor for the maze bot later
2More

Nxt - 7 views

www.ece.gatech.edu/...NXT%20lab%203.pdf
shared by Thomas Helm on 12 Mar 12 - No Cached
  • Thaddeus McKeon on 12 Mar 12
     
    this shows how to get an NXT to keep on the line where it should turn and all taht good stuff
  • Thomas Corcoran on 12 Mar 12
     
    shows different light sensor values you should get around when you are going off the tape
2More

How to make a line follower with only one sensor - Andy的網路日誌 - 無名小站 - 3 views

www.wretch.cc/...23114583
shared by Bryan Kelleher on 12 Mar 12 - No Cached
  • Bryan Kelleher on 12 Mar 12
     
    This is a good way to find the line if you may have fallen off of it.
  • Anthony DiVirgilio on 12 Mar 12
     
    this is a good way to make sure you dont lose the line
1More

Vision Subsystem v4 for NXT (NXTCam-v4) - www.mindsensors.com - 1 views

www.mindsensors.com/index.php
shared by Alexander Laferriere on 12 Mar 12 - Cached
  • Bryan Kelleher on 12 Mar 12
     
    what does this do?
2More

http://drgraeme.net/DrGraeme-free-NXT-G-tutorials/Ch102/Ch102V1G/default.htm - 0 views

drgraeme.net/...default.htm motion following line
shared by Anthony DiVirgilio on 12 Mar 12 - No Cached
  • light sensor moved towards, and then away, from the line edge, (and then again towards, and then away, and so on…) as shown in the two photos below.
  • Thaddeus McKeon on 12 Mar 12
     
    I know we don't have 2 light sensors but it is nice to know one way of doing it
« First ‹ Previous 41 - 60 of 178 Next › Last »
Showing 20▼ items per page