AD90 Transponder Key Duplicator Plus System version V3.27 features the most innovative electronic components in the field of radio frequencies thus allowing easy detection, reading and cloning (duplication) of fixed code transponders and the identification of cryptographic transponder codes.
MPPS v12.01 Chip-Tuning, MPPS v12.01,lastest version, MPPS s update to v12.1,allows read and write memory from the car computer via the diagnostic connector. It supports the latest drivers EDC16, EDC17, MED9.x, Siemens PPD1/x, EDC15, ME7.xi much more.
Powergate is a programmer via OBD2 diagnostic plug. It has the latest protocols of communication (K-LINE, CAN and J1850), Powergate can read and write the Electronic Control Unit of many vehicles on the market. It also can read and erase DTC Errors.
The XPROG-m programmer is designed to replace the earlier version of XPROG programmer. The XPROG-m supports in-circuit and on-board programming of Motorola 68HC05, 68HC08, 68HC11, 68HC(S)12 family MCU's, Texas Instruments TMS370/TMS374 family MCU's and serial EEPROM's.
UPA USB Programmer is the best programmer that supports Motorola and others chip programming. Unlike other programmers, the UPA-USB can support many devices in a single unit.
Serial Suite Piasini Engineering V4.1 MASTER is full kit of PIASINI and master version. It includes all function in list of the following it can read all dump of chip by bin file. And you can write or edit this dump by yourself.
CAR PROG is a universal EEPROM tool that allows to read, write, edit and erase various types of EEPROM memories. I2C, SPI and Microwire memory interfaces are supported. Device is communicating with PC through USB port.
SMPS MPPS V5 ECU Chip Tuning Tool For EDC15 EDC16 EDC17 is a USB chip tuning interface, this is good clone working with V5.0 version of software. This interface lets you to read and write memory of a car computer through the diagnostic connector.
SMPS MPPS V5 ECU Chip Tuning Tool For EDC15 EDC16 EDC17 is a USB chip tuning interface. This is good clone working with V5.0 version of software. This interface lets you to read and write memory of a car computer through the diagnostic connector.
REVO is a Car Chip-Turning, Engineered Performance for your cars. RevoFlash 3 works for VW,AUDI, SEAT and SKODA. It do a car only need 10 minutes and only need put the SPP cable to the socket of diagnostic in your car and open the software.
SMPS MPPS V5 ECU Chip Tuning Tool For EDC15 EDC16 EDC17 is a USB chip tuning interface. This is good clone working with V5.0 version of software. This interface lets you to read and write memory of a car computer through the diagnostic connector.
This Tool is a frequency sweeper with 5V square wave output (Duty cycle 50%, effective frequency range from over 10kHz (max 50kHz) to 50Hz). This tool can be also considered as a MCU version of the software TMS-374 Decoder ECU. The only difference between the two tools is that the MCU version works without a PC.
The XPROG-m programmer is designed to replace the earlier version of XPROG programmer, XPROG-m programmer is fully upward-compatible hardware with XPROG programmer and have many additional features.
The memory for SPI 28 software and data is implemented as a programmable component into ECU for a long time now. Ever since these components are erasable even as an assembled part of the ECU more and more vehicle manufacturers chose to provide the possibility to re-load/replace the software and data contents of the respective control unit in addition to the analysis and error detection mechanisms.
MCU controlled Interface for Mercedes Benz Car soft 7.4 brand new. You can read/erase all fault codes with this device, and also can read ECU information.
