Group items tagged

HINO Trucks diagnostics is a tool equipped with all the functions needed to diagnose the trouble, check functions, and configure the settings of the electronic system built into HINO engines. The program runs on a personal computer equipped with a Windows95/98/200/xp operating system, And it connects to a communication network by means of a diagnosis connector via a communication Interface. After it has been connected to a communication network, it can carry out various operations by extracting information from the engine ECU.

Mangoose toyota diagnostics and reprogramming interface is a low-cost, high-performance vehicle network interface that connects a laptop directly to the OBD-II connector. Mangoose toyota interface can diagnose and reprogram Toyota vehicles. The DrewTech Mongoose is a USB pass-thru device that utilizes the SAE J2534-1 API, which means that Mangoose uses a standard communications interface to the vehicle, allowing it to work with 3rd party diagnostic applications.

This Tool is a frequency sweeper with 5V square wave output (Duty cycle 50%, effective frequency range from over 10kHz (max 50kHz) to 50Hz). This tool can be also considered as a MCU version of the software TMS-374 Decoder ECU. The only difference between the two tools is that the MCU version works without a PC.

Jaguar & Land Rover are now fully supported for dealer level diagnostics & module programming with the new Mongoose JLR. Jaguar / Land Rover have approved this tool as a supported interface and now offer the Mongoose JLR to their own dealership service centers as a factory diagnostics tool. Coverage includes 1999 & Up Jaguar and 2005 & up Land Rover, requires a subscription to IDS version 125 & up. This is the full blown Jaguar & Land Rover maintenance diagnostic & module reprogramming hardware. Use the Mongoose JLR directly with the software (available from Jaguar / Land Rover) on your own laptop or PC and see the same results the dealer sees.

This is a touch screen without LCD for all Launch X431, includes x431 Master, x431 GX3 and X431 old model. It is only a touch screen parts, does not include LCD. When your Launch X431 touch screen broken or can not work, you need a new touch screen to fix it.

The memory for SPI 28 software and data is implemented as a programmable component into ECU for a long time now. Ever since these components are erasable even as an assembled part of the ECU more and more vehicle manufacturers chose to provide the possibility to re-load/replace the software and data contents of the respective control unit in addition to the analysis and error detection mechanisms.

SMPS MPPS V5 ECU Chip Tuning Tool For EDC15 EDC16 EDC17 is a USB chip tuning interface. This is good clone working with V5.0 version of software. This interface lets you to read and write memory of a car computer through the diagnostic connector.

SMPS MPPS V5 ECU Chip Tuning Tool For EDC15 EDC16 EDC17 is a USB chip tuning interface, this is good clone working with V5.0 version of software. This interface lets you to read and write memory of a car computer through the diagnostic connector.

REVO is a Car Chip-Turning, Engineered Performance for your cars. RevoFlash 3 works for VW,AUDI, SEAT and SKODA. It do a car only need 10 minutes and only need put the SPP cable to the socket of diagnostic in your car and open the software.

SMPS MPPS V5 ECU Chip Tuning Tool For EDC15 EDC16 EDC17 is a USB chip tuning interface. This is good clone working with V5.0 version of software. This interface lets you to read and write memory of a car computer through the diagnostic connector.

This is a touch screen for all Launch X431, includes x431 Master, x431 GX3 and X431 old model. It is full set, include LCD screen and touch screen. When your Launch X431 Screen broken. You need a new full set touch screen.

This is a touch screen for Launch X431 Diagun. It is full set, include LCD screen and touch screen. When your Launch X431 Diagun Screen broken. You need a new full set touch screen.

Launch X431 Diagun Yellow & Red Box are a part of Diagun. It is designed and produce by Launch. It is 100% original Diagun box. Some customers Diagun box were broken or too old. So to change a new box is the best selection because it is cheaper.

Launch X431 Diagun Main Unit Shell is a part of Diagun. It is designed and produce by Launch. It is 100% original Diagun Shell. Some customers Diagun main unite shell was broken or too old. So to change a new Shell is the best selection because it is cheaper.

OP-COM is a PC based diagnostic program, it covers almost all Opel cars, the program lets you to read out and clear fault codes, shows you live data, lets you to perform output test, and supports remote, and key programming.The program supports many control units, like Engine, Automatic Transmission, ABS, Airbag, Engine Cooling module, Instrument Cluster, Electronic Climate Control, Body Control Unit, just to name a few examples. The diagnostic inteface is USB port based, so there will be NO COMPATIBILITY ISSUES, with serial to USB converters.

VAG 10.6.3,10.6.4,11.2,11.8,11.10Dignostic Tools is fully compatible with all VW, Audi, Seat and Skoda models through the current model year, including models using a direct CAN connection for diagnostics, and have a database of more than 14000 fault-codes and measuring-block texts.

CarBrain C168 scanner is a wireless automotive fault diagnostic tool and support maintenance records management and standard UBS port, C168 scanner is easy to use and excellent performance with bluetooth technology, working with a full range coverage of vehicles, also can be installed on most equipments that have Windows operating system.

Fiat ECU Scan Diagnostic Tool for Fiat Alfa Romeo and Lancia, It support Engin, Airbag, ABS, Power Steering and CAN systems, Fiat ECU Scan Diagnostic Tool bundle for FiatECUScan software, compatible fully with fiateucscan. It work on a laptop or PC running Windows XP, Vista or Windows 7 with a USB port.

It is a complete full set BMW ICOM system with ISTA-D and ISSS ISTA/P. It works on the newest F-series models. BMW ICOM full set system including everything you need, it includes diagnose, program and code for all BMW up to 2011. It includes BMW ICOM A+B+C, new IBM X201 laptop and software (ISTA-D 2.27+ ISTA-P 2.43).

Obd2s Store for high quality fly 108 programmer for all honda ,ford and mazda products with a low price, FLY Scanner Honda is a professional diagnostic tool, compared with FLY108,FLY108-PRO can realize coding and immo function for Ford and Mazda.